Kia Soul EV: Restraint / General Safety Information and Caution
Kia Soul EV (PS EV) 2015-2020 Service Manual / Restraint / General Safety Information and Caution
| Precautions |
| General Precautions |
Please read the following precautions carefully before performing the airbag system service.
Carefully observe the instructions described in this manual
as misuse of airbags may result in accidental deployment of airbags,
damage or injuries.
| • |
Except when performing electrical inspections, always turn
the ignition switch OFF and disconnect the negative cable from the
battery, and wait at least three minutes before beginning to work. |
The contents in the memory are not erased even if the
ignition switch is turned OFF or the battery cables are disconnected
from the battery. |
| • |
Use only the replacement parts manufactured to the same standards and quality as the original parts..
Do not reuse SRS parts removed from other vehicles. Use only new parts when repairing the SRS. |
| • |
Carefully inspect any SRS parts before installation. Do not
install any parts that show signs of being dropped or improperly
handled, such as dents, cracks or deformation.
|
| • |
Before removing any of the SRS parts (including the disconnection of the connectors), always disconnect the SRS connector. |
Airbag Handling and Storage
Do not disassemble the airbags as there are no serviceable
parts. Once an airbag has been deployed, it cannot be repaired nor
reused.
For temporary storage of the air bag during service, please observe the following precautions:
| • |
Store the removed airbag with the pad surface up. |
| • |
Keep free from any oil, grease, detergent, or water to prevent damage to the airbag assembly.
|
| • |
Store the removed airbag on secure, flat surface away from any high heat source (exceeding 85 C/185 F). |
| • |
Never perform any electrical inspections, such as measuring resistance, to the airbags. |
| • |
Do not position yourself in front of the airbag assembly during removal, inspection, or replacement. |
| • |
Refer to the scrapping procedures for disposal of the damaged airbag. |
| • |
Be careful not to impact or bump on the SRS unit, the side
impact sensors or the front impact sensors whenever the ignition switch
is ON. Wait for at least three minutes after the ignition switch is
turned OFF before beginning to work. |
| • |
During installation or replacement, be careful not to bump on
the area (by impacting with a wrench, hammer, etc.) around the SRS
unit, the side impact sensor and the front impact sensor as any impact
on the airbags may accidentally deploy them to cause possible damage or
injury. |
| • |
Replace the front airbag module, SRSCM and FIS after the
front airbag is deployed. Replace the airbag wiring if it is damaged.
Replace the side airbag module, the curtain airbag module, SRSCM and SIS
after the side airbag is deployed. Replace the airbag wiring if it is
damaged. |
| • |
If the airbags or the side airbags were not deployed in a
collision, inspect for any damage or deformation on the SRS unit and the
side impact sensors. If any damage is found, replace the SRS unit, the
front impact sensor and/or the side impact sensors. |
| • |
Do not disassemble the SRS unit, the front impact sensor or the side impact sensors. |
| • |
Turn the ignition switch OFF, disconnect the battery negative
cable and wait for at least three minutes before beginning to install
or replace the SRS unit. |
| • |
Be sure that the SRS unit, the front impact sensor and side impact sensors are installed securely with mounting bolts. |
| • |
Be careful not to spill water or oil on the SRS unit, the
front impact sensor or the side impact sensors and keep them away from
dust. |
| • |
Store the SRS unit, the front impact sensor and the side
impact sensors in a cool (15 ~ 25 C/ 59 ~ 77 F) and dry (30 ~ 80%
relative humidity, no moisture) area. |
Wiring Precautions
SRS wiring can be identified by special yellow outer covering. Observe the instructions described in this section.
| • |
Never attempt to modify, splice or repair SRS wiring. If there is an opening or damage on SRS wiring, replace the harness.
|
| • |
Be sure to install the harness wires so that they are not pinched, or interfering with other parts.
|
| • |
Make sure all SRS ground locations are clean, and grounds are
securely fastened for optimum metal-to-metal contact. Poor grounding
can cause intermittent problems that are difficult to diagnose. |
Precautions for Electrical Inspections
| • |
When using electrical test equipment, insert the probe of the tester into the wire side of the connector.
Do not insert the probe of the tester into the terminal side of the connector, and do not tamper with the connector.
|
| • |
Use a u-shaped probe. Do not force the probe into a connector. |
| • |
Use specified service connectors for troubleshooting.
Using improper tools could cause an error in inspection due to poor metal contact. |
Spring-loaded Lock Connector
Some SRS system connectors come with spring-loaded locks.
Airbag Connector
| Disconnecting |
To release the lock, pull the spring-loaded sleeve (A) and the slider (B) while holding the opposite half of the connector.
Pull the connector halves apart. Be sure to pull on the sleeve instead of the connector half.
| Connecting |
Hold both connector halves and press firmly until the projection(C) of the sleeve-side connector clicks to lock.
Special Service Tools
Special Service Tools
Tool Name / NumberIllustrationDescriptionDeployment tool0957A-34100AUsed for deploying airbagDeployment adapter0957A-3F100Used with the deployment tool (0957A-34100A) to dep ...
Repair procedures
Component Replacement after Deployment
Before doing any SRS repairs, use the GDS to check for DTCs.
Refer to the Diagnostic Trouble Code list for repairing of the rel ...
Other information:
Kia Soul EV (PS EV) 2015-2020 Service Manual: EPB Switch Repair procedures
Removal 1. Turn ignition OFF and disconnect the negative (-) battery cable. 2. Remove the floor console upper cover. (Refer to Body group - "Console") 3. Remove the EPB switch assembly. Installation 1. Install the EPB switch assembly to the floor console upper cover. 2. ...
Kia Soul EV (PS EV) 2015-2020 Service Manual: Condenser Repair procedures
Inspection 1. Check the condenser fins for clogging and damage. If clogged, clean them with water, and blow them with compressed air. If bent, gently bend them using a screwdriver or pliers. 2. Check the condenser connections for leakage, and repair or replace it, if required. Replaceme ...
Copyright © www.ksoulev.com 2020-2024
